|
+ Barcode Reader |
+ RFID Reader |
|
▼
Mailing Address | |
No. 4, Jalan Industri Mas 7, | |
Tmn. Mas, 47100 Puchong, | |
Selangor D.E. Malaysia. |
|
|
| |
|
|
▼
MSN ID |
symbotec@hotmail.com |
|
|
▼
SKYPE ID |
symbotec |
|
|
|
|
|
 |
|
|
©
Symbotec.com 2010-2011 |
|
| |
|
|◄ Back |
Page
1 / 1 |
Next ►►| |
><
>< ><
Direct Part Marking Technology : By Category ><
><
>< |
|
 |
|
| |
►
Electrochemical Etcher | |
Marking Depth : < 0.01 mm. | |
Marking Speed : Below Average. | |
Advantages : Low start up & operating cost, easy to operate. | |
Good for : Most of the Metallic (electricity conductive) materials. |
|
|
|
|
 |
|
| |
►
Dot Peen Marker | |
Marking Depth : < 0.5 mm. | |
Marking Speed : Average. | |
Advantages : High speed, low operating cost, computerized. | |
Good for : Material with hardness less than 62 HRC and not brittle. |
|
|
|
 |
|
| |
►
Inkjet Coder | |
Marking Depth : Non-Destructive. | |
Marking Speed : Above Average. | |
Advantages : High speed, low operating cost, removable. | |
Good for : All materials that are free from grease and oil. |
|
|
|
|
 |
|
| |
►
LASER Engraver | |
Marking Depth : < 0.05 mm. | |
Marking Speed : Above Average. | |
Advantages : Superior finishing, none impact, high speed. | |
Good for : (CO2) glass, wood, plastic, fabric; (YAG) metal. |
|
|
|
 |
|
| |
►
Handy Engraver | |
Marking Depth : < 0.1 mm. | |
Marking Speed : Below Average. | |
Advantages : Portable, handy, easy to operate, low cost. | |
Good for : Plastic, glass, wood, metal, rubber, ceramic & etc. |
|
|
|
|
 |
|
| |
►
Rotary Engraver | |
Marking Depth : < 0.4 mm. | |
Marking Speed : Below Average. | |
Advantages : Low start up and operating cost, easy to operate. | |
Good for : (Carbide) 2-ply ABS, plastic; (Diamond) metal, glass. |
|
|
|
 |
|
| |
►
Scribe Marker | |
Marking Depth : < 0.6 mm. | |
Marking Speed : Average. | |
Advantages : High speed, deep marking, computerized. | |
Good for : Metal casting, engine casting, steel structure & pipes. |
|
|
|
|
 |
|
| |
►
Stamp Press Marker | |
Marking Depth : < 0.5 mm. | |
Marking Speed : Average. | |
Advantages : Low start up cost, easy to operate, high speed. | |
Good for : Metal surface with hardness less than 70 HRC. |
|
|
|
|
|
|◄ Back |
Page
1 / 1 |
Next ►►| |
| No. 34-1-1, Level 1, Medan Putra Business Centre, Bandar Sri Menjalara, 52200 Kuala Lumpur, Malaysia. | |
Tel: +603-6275 3755 Fax: +603-6276 3755 Email: malaysia@symbotec.com |
|
|
